WOW, hard to believe that it's been six years since I was first inquiring about this (viewtopic.php?p=46049#p46049)!
Many projects have kept me away from doing repairs on the home. Now that they're finished I'll be, finally, getting around to the home, but only come Spring of 2018.
As had been mentioned in that post of mine linked above, my home sits on a concrete slab. The skirting on the ends of the home extend to and past the edges of the slab (but basically not below). On the front and back, however, the slab extends a good 4 inches (or six). I don't believe that this is proper: I know that for stick-built homes/buildings that the sill plates will come to the edge of the slab and the siding will then overlap such that it hangs past and down the slab; this allows any water to escape down and outside the slab. Am I wrong in thinking that this same construction principle should be used with manufactured/mobile homes as well?
While I may install Hardi-Plank, which would be impervious to water, I'd still like to do things right if I'm tearing things apart. I figure that I could just run a concrete saw to trim off that extra width of slab (there's nothing depending on it other than a couple posts my front deck is setting on- the deck will be completely replaced, so no concerns there).
Should skirting hang over edge of slab?
Moderators: Greg, Mark, mhrAJ333, JD
There really is no cut and dry way to install the bottom as long as it is sealed up. The cleanest looking would be to set the track on the concrete.
You have to remember that when the pad was poured they did not have the exact measurements plus the mover would have to do an perfect placement of the home when it was set up.
Greg
You have to remember that when the pad was poured they did not have the exact measurements plus the mover would have to do an perfect placement of the home when it was set up.
Greg
"If I can't fix it, I can screw it up so bad no one else can either."
Hi, Greg!
No tracks, just pressure treated wood framing for attaching the T1-11 skirting. The sealer along the bottom has long since departed.
Haven't looked at this in quite a while. I seem to recall that they had attached the skirt frame to the home, which I thought wasn't correct?
No tracks, just pressure treated wood framing for attaching the T1-11 skirting. The sealer along the bottom has long since departed.
Haven't looked at this in quite a while. I seem to recall that they had attached the skirt frame to the home, which I thought wasn't correct?
Again, if you ask 10 people you will get 10 answers. Here is one manufacturer's instructions
https://www.skirtingdirect.com/pdf/viny ... ctions.pdf
I used insulated concrete roof panels on our's so it was a "wing it as you go" job.
viewtopic.php?f=6&t=10629&p=55511&hilit ... ing#p55511
The final goal is something that looks good and keeps weather & critters out.
Greg
https://www.skirtingdirect.com/pdf/viny ... ctions.pdf
I used insulated concrete roof panels on our's so it was a "wing it as you go" job.
viewtopic.php?f=6&t=10629&p=55511&hilit ... ing#p55511
The final goal is something that looks good and keeps weather & critters out.
Greg
"If I can't fix it, I can screw it up so bad no one else can either."
OK, thanks for the input. I'll do some more pondering. But...
Is it correct that the skirting should be free floating, not attached to the home itself? (reason for the tracks [upper]?) As mentioned, I have some framing for the skirting and (I believe) they connected it to the rim joist. The skirting (T1-11) is then screwed to this frame. The top edge of the skirting comes under a trim piece; no flashing. The trim piece (ugh, someone installed it with the wrong nails- bleeding rust!) needs to go.
I need to take and post a picture.
Is it correct that the skirting should be free floating, not attached to the home itself? (reason for the tracks [upper]?) As mentioned, I have some framing for the skirting and (I believe) they connected it to the rim joist. The skirting (T1-11) is then screwed to this frame. The top edge of the skirting comes under a trim piece; no flashing. The trim piece (ugh, someone installed it with the wrong nails- bleeding rust!) needs to go.
I need to take and post a picture.
In most applications there should be a top rail to allow for ground or home movement during the freezing weather.
I decided to try a shallow track (metal 2x4) screwed to the bottom of the rim joist when I did ours. The home is set on 18" piers 48" deep so frost is not going to move the home.
I think the band you are seeing in the picture is a 2x that I used to align & support the steel skirting. The concrete shirting is in the ground a minimum of 6-8". I replaced the 8" white trim with a grey trim after I finished the skirting.
Greg
I decided to try a shallow track (metal 2x4) screwed to the bottom of the rim joist when I did ours. The home is set on 18" piers 48" deep so frost is not going to move the home.
I think the band you are seeing in the picture is a 2x that I used to align & support the steel skirting. The concrete shirting is in the ground a minimum of 6-8". I replaced the 8" white trim with a grey trim after I finished the skirting.
Greg
You do not have the required permissions to view the files attached to this post.
"If I can't fix it, I can screw it up so bad no one else can either."
Greg, I really like what you did. I can't seem to find those panels around anywhere. How do/did you facilitate access "doors?"
Here's a picture that kind of shows the situation I have, the extra width on the slab, and the skirting framing (note top is attached directly to home):
Here's a picture that kind of shows the situation I have, the extra width on the slab, and the skirting framing (note top is attached directly to home):
You do not have the required permissions to view the files attached to this post.
Those were insulated concrete panels that same off of a commercial building that were used to protect a rubber roof.
For the access panel I cut the access hole in the panel and framed it with pressure treated wood.
In most cases the top of the skirting should be allowed to float. If you are in a region that does not freeze you may be fine with solid mount.
Greg
For the access panel I cut the access hole in the panel and framed it with pressure treated wood.
In most cases the top of the skirting should be allowed to float. If you are in a region that does not freeze you may be fine with solid mount.
Greg
"If I can't fix it, I can screw it up so bad no one else can either."
On a slab you should be OK as long as the slab was installed correctly. I have seen cases of poor installations where the whole slab shifted and cracked.
Greg
Greg
"If I can't fix it, I can screw it up so bad no one else can either."
-
- Similar Topics
- Replies
- Views
- Last post
-
-
I need input on best way to hang new copper or pex pipes from underside mobilehome without opening up belly board
by waitingtohear » Mon Jun 11, 2018 12:21 am » in Mobile Home Repair - 7 Replies
- 89635 Views
-
Last post by waitingtohear
Mon Jul 02, 2018 5:39 pm
-
-
- 4 Replies
- 12453 Views
-
Last post by spinner357
Thu Aug 24, 2017 10:33 am
-
-
Edge of underfloor coming up under linoleum
by MizFurball2u » Fri Jun 01, 2018 12:48 am » in Mobile Home Repair - 5 Replies
- 37211 Views
-
Last post by MizFurball2u
Sun Jun 03, 2018 11:04 pm
-
-
-
Drywall, what thickness should I use for the walls?
by ChuckS59 » Sun Jan 27, 2019 1:35 pm » in Mobile Home Repair - 2 Replies
- 12898 Views
-
Last post by ChuckS59
Tue Jan 29, 2019 6:21 pm
-
-
-
Should windows have gaps like this??
by samantha_dahman » Thu May 28, 2020 7:11 am » in Mobile Home Repair - 3 Replies
- 29902 Views
-
Last post by samantha_dahman
Tue Jun 02, 2020 7:02 pm
-