Hi,
If the ignitor stays energized too long, could be a short in wiring, bad control board, bad t-stat.
Check burner orifice for a blockage like spider/web.
Thanks,
Robert
problems with coleman evcon
-
- Posts: 18
- Joined: Mon Nov 16, 2009 8:45 am
okay i had my furnace guy come and check my gas valve pressure..had 11 lbs going in and 7 lbs coming out..bout a new valve for $65 going to install it today...hopefully that solves this lil problem..thanks again rober..youve been a tremndous help
-
- Posts: 18
- Joined: Mon Nov 16, 2009 8:45 am
hey Robert,,
installed new valve,,still wouldnt fire..called a buddy @ g.w berkhimer and he had me tape together the wires on the highlimit switch..furnace fired and is running fine..can you give me the part # for that switch..it is the one closest to the combustion motor...thanks again..hopefully you wont here from me after this..thanks
installed new valve,,still wouldnt fire..called a buddy @ g.w berkhimer and he had me tape together the wires on the highlimit switch..furnace fired and is running fine..can you give me the part # for that switch..it is the one closest to the combustion motor...thanks again..hopefully you wont here from me after this..thanks
Hi,
Limit Switch # 7995 - 3281/A can be seen and ordered through PayPal from right side of this page:
http://www.mobilehomerepair.com/ColemanGas.html
Thanks,
Robert
Limit Switch # 7995 - 3281/A can be seen and ordered through PayPal from right side of this page:
http://www.mobilehomerepair.com/ColemanGas.html
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Posts: 18
- Joined: Mon Nov 16, 2009 8:45 am
hi Robert
okay..limit switch is in and still acting up...now the glow plug will come on for 2 seconds and go out,,come on again real quick but then go out again.??i hear it clicking in the ignition control,..do you think the ignition control or the sequencers are bad.???
okay..limit switch is in and still acting up...now the glow plug will come on for 2 seconds and go out,,come on again real quick but then go out again.??i hear it clicking in the ignition control,..do you think the ignition control or the sequencers are bad.???
Hi,
You don't have any sequencers. Need to test circuit with a meter to find problem. Could be a shorted wire. Replacing parts looking for problem is wasting a lot of dollars unnecessarily.
Look closely for loose wire connections, bare spots on wire and shorts in wiring.
The components in the circuit have to receive power and keep it for designed length of time.
Only after ensuring that was happening, would it be time to start testing and eliminating components.
Thanks,
Robert
You don't have any sequencers. Need to test circuit with a meter to find problem. Could be a shorted wire. Replacing parts looking for problem is wasting a lot of dollars unnecessarily.
Look closely for loose wire connections, bare spots on wire and shorts in wiring.
The components in the circuit have to receive power and keep it for designed length of time.
Only after ensuring that was happening, would it be time to start testing and eliminating components.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Posts: 18
- Joined: Mon Nov 16, 2009 8:45 am
hey robert...i ended up replacing the ignition control...furnace seems to work fine with the exception of the exhausat motor continuing to run after the furnace shuts down.??any ideas what this can mean...thanks again
-
- Similar Topics
- Replies
- Views
- Last post
-
- 0 Replies
- 45137 Views
-
Last post by chrismc_us
Mon Dec 23, 2019 9:00 am
-
-
2-combo single pole lightswitch problems
by hstassen » Mon Jan 06, 2020 9:41 pm » in Mobile Home Repair - 2 Replies
- 13603 Views
-
Last post by Greg
Tue Jan 07, 2020 6:12 pm
-
-
- 0 Replies
- 110048 Views
-
Last post by cwwhite75
Sat Feb 29, 2020 8:46 am
-
-
Colman evcon presidental 7980B856 furnace will not stay on
by ezridersid » Sat Dec 21, 2019 8:52 pm » in Mobile Home Repair - 1 Replies
- 17306 Views
-
Last post by ezridersid
Sat Dec 21, 2019 9:04 pm
-
-
-
Transformer burning out in an Evcon DES 80
by BigDave67s » Wed Dec 29, 2021 10:01 pm » in Coleman Service & Repair - 0 Replies
- 111980 Views
-
Last post by BigDave67s
Wed Dec 29, 2021 10:01 pm
-