I have a coleman furnace model#DGAT056BDD Serial #970346567 We just replaced roof jack and gas valve because the repair man said it was needed after changing the valve our blower will come on and go back off again about 6-10 times befor it will stay on and run through the cycle just fine. this was not doing this before we put the new valve in. we did this work ourselves because of the price it would cost for them to. do you have any suggestions for us to try Thank-You
Shannon
Coleman modelDGAT056BDD
-
- Posts: 4
- Joined: Sun Dec 27, 2009 5:58 pm
Not trying to steal Shannon's thunder or anything but I have the EXACT same problem except we have not replaced anything like she (or he!) has. We moved in a few months ago and it has always done the really short cycles until it eventually stays on. The burner stays lit the whole time, just the blower will do very annoying constant short cycles-- 5 or 10 seconds, then cut off...back on...off...on...off... then eventually stay on to heat the house. I have replaced the thermostat with a digital and really don't think it is the problem anyhow (also replaced the upper limit a few months ago).
I have the same model except mine is 70,000 BTU..
I have the same model except mine is 70,000 BTU..
Hi Shannon,
Inspect the burner and burner orifice behind the gas valve for blockages. Look for spider-web-eggs especially.
If ok need to have gas pressures checked by hvac tech.
Thanks,
Robert
Inspect the burner and burner orifice behind the gas valve for blockages. Look for spider-web-eggs especially.
If ok need to have gas pressures checked by hvac tech.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
HI Robert
I have had the pressure checked by gas company they said the pressure was really good right where it should be.They seem to be puzzled why it is doing it. They mention maybe the circut board but they said they have never seen one do this in the newer furnaces
I have had the pressure checked by gas company they said the pressure was really good right where it should be.They seem to be puzzled why it is doing it. They mention maybe the circut board but they said they have never seen one do this in the newer furnaces
Is burner and burner orifice clear ? If so, could be the control board, but would need to test the board to know.
Thanks,
Robert
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Does the burner stay ignited while blower is cutting in and out ? If so, does it appear to be a normal good and strong flame ?
Thanks,
Robert
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Similar Topics
- Replies
- Views
- Last post
-
- 0 Replies
- 57606 Views
-
Last post by Montanan
Wed Jan 03, 2018 1:03 pm
-
- 0 Replies
- 50153 Views
-
Last post by Kourgath
Fri Mar 23, 2018 3:41 pm
-
-
LOUD Blower on Coleman Presidential 2 900759
by AuntKatie » Thu Apr 05, 2018 6:50 pm » in Coleman Service & Repair - 0 Replies
- 44869 Views
-
Last post by AuntKatie
Thu Apr 05, 2018 6:50 pm
-
-
-
Eb12eb Coleman furnace 4 speed help.
by Johnwayne892000 » Thu Aug 30, 2018 7:37 pm » in Coleman Service & Repair - 0 Replies
- 25015 Views
-
Last post by Johnwayne892000
Thu Aug 30, 2018 7:37 pm
-
-
-
Coleman 6806a furnace doesn't stop heating even with tstat disconnected. Any ideas?
by Neighbor Bill » Mon Dec 31, 2018 1:01 pm » in Coleman Service & Repair - 1 Replies
- 41740 Views
-
Last post by Neighbor Bill
Mon Dec 31, 2018 1:06 pm
-