burner and pilot blow out
-
- Posts: 2
- Joined: Tue Nov 30, 2010 4:08 am
coleman presidential 2--model 7700a--pilot and burner was out--I lit it and when the burner came on it ran about 20 secs and all went out--as if sucked out--I thought it was therno-couple so replaced burner and thermo couple control unit attached to burner--still same thing--flame gets some orange,seems disterbed(even more by combustion fan) burns 10-20 secs and go's out
-
- Posts: 23
- Joined: Fri Oct 09, 2009 11:07 am
ck roof jack for seperation, flame should be blue.
does pilot stay lite after u light it, w/o out going out. If so, when blower kicks on does the flame move alot.
its possible u may have a spider web in the pilot tube/ burner or even in the spud behing the gas valve.
Let me know what the flame does after the blower comes on, then we will go from there.
a gentlemen by the name of robert may reply to u before i get back to u, if so, pay attention, he's the ace on mobile home units
does pilot stay lite after u light it, w/o out going out. If so, when blower kicks on does the flame move alot.
its possible u may have a spider web in the pilot tube/ burner or even in the spud behing the gas valve.
Let me know what the flame does after the blower comes on, then we will go from there.
a gentlemen by the name of robert may reply to u before i get back to u, if so, pay attention, he's the ace on mobile home units
Is the small booster vent motor remaining running ? It should be first thing to come on and MUST remain on throughout the cycle.
Check what furnaceman mentioned. Also be sure booster motor is running strong and it and wheel are clean.
Make sure you maintain a 24vac signal to gas valve throughout cyle as well
IF all that is ok, will need hvac tech to check gas valve operation and gas pressures next.
Be SURE the burner orifice/spud, burner tube, pilot tubibg and pilot burner are ALL clean and clear.
Thanks,
Robert
Check what furnaceman mentioned. Also be sure booster motor is running strong and it and wheel are clean.
Make sure you maintain a 24vac signal to gas valve throughout cyle as well
IF all that is ok, will need hvac tech to check gas valve operation and gas pressures next.
Be SURE the burner orifice/spud, burner tube, pilot tubibg and pilot burner are ALL clean and clear.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Similar Topics
- Replies
- Views
- Last post
-
-
intertherm standing pilot propane burner Heat Rise of 38°F spread.
by justplumducky » Fri Aug 25, 2017 10:06 am » in Nordyne Service & Repair - 0 Replies
- 55122 Views
-
Last post by justplumducky
Fri Aug 25, 2017 10:06 am
-
-
-
Intertherm standing pilot LPG burner 77 BTU IN gas valve mounting plate gets hot ( not warm).
by justplumducky » Sat Sep 09, 2017 3:34 am » in Nordyne Service & Repair - 1 Replies
- 74900 Views
-
Last post by Maxwell.lipphardt
Thu Nov 22, 2018 10:15 am
-
-
- 2 Replies
- 20919 Views
-
Last post by TorstenW
Tue Mar 06, 2018 1:04 am
-
-
Need to remove a stripped Allen wrench-type plug from the OUT PRESS port on top of gas valve
by justplumducky » Fri Aug 25, 2017 8:21 am » in Nordyne Service & Repair - 1 Replies
- 49086 Views
-
Last post by Maxwell.lipphardt
Mon Feb 04, 2019 6:29 am
-
-
-
Intertherm outdoor a/c unit, blower not turning off. Model unknown rating plate is faded out.
by tkrueger » Sat May 05, 2018 8:57 pm » in Nordyne Service & Repair - 0 Replies
- 116448 Views
-
Last post by tkrueger
Sat May 05, 2018 8:57 pm
-