Looking for spec sheets and such
Moderators: Greg, Mark, mhrAJ333, JD
I have been all over the internet trying to find spec sheets floor plan drawing etc for my house and am getting nowhere. Does anyone has a number, address something for Schult homes? If I gave them a serial number could they give me exact details for the house?
Erick, it is not impossible to find the prints, but I will say it is difficult at best. For some reason, weather it is the anount of optional layouts or just the fact they don't want the info out there or even don't have it any more. Many people have tried with very limited success. Your best bet may be to get in touch with the manufacturer or dealer. Greg
"If I can't fix it, I can screw it up so bad no one else can either."
Hi Erick,
We are on the same mission. I have contacted Sunshine Homes twice (by email) and they have not responded. These homes are built to code so you'd think these guys would keep blueprints for a certain number of years. Here is the contact page for Schult: http://www.schulthomes.com/contact_us/index.cfm, you can even enter a model number but if it is too old you may never find it. My owners manual says that if I ask for it in writing, they will furnish a diagram of the structural, electrical, plumbing and heating, cooling and transportation systems. Your request should contain the model identification and serial number and the location of the plant that built it (see the data plate). As far as I can tell, the data plate is a piece of paper inside the cabinet. There has got to be a permanent one somewhere else.
Good luck,
Charliemom
We are on the same mission. I have contacted Sunshine Homes twice (by email) and they have not responded. These homes are built to code so you'd think these guys would keep blueprints for a certain number of years. Here is the contact page for Schult: http://www.schulthomes.com/contact_us/index.cfm, you can even enter a model number but if it is too old you may never find it. My owners manual says that if I ask for it in writing, they will furnish a diagram of the structural, electrical, plumbing and heating, cooling and transportation systems. Your request should contain the model identification and serial number and the location of the plant that built it (see the data plate). As far as I can tell, the data plate is a piece of paper inside the cabinet. There has got to be a permanent one somewhere else.
Good luck,
Charliemom
I believe that data sheet either glued to an interior cupboard or in a closet is the permanent data sheet.
If your home is real old then these have generally been painted over or removed do to repairs or renovation. There is also a metal ID tag riveted to the end of the home, unless like ours it has been vinyl sided over. A doublewide will have 2 of these plates.
~Yanita~
If your home is real old then these have generally been painted over or removed do to repairs or renovation. There is also a metal ID tag riveted to the end of the home, unless like ours it has been vinyl sided over. A doublewide will have 2 of these plates.
~Yanita~
The difference between success and failure is who gives up first!
Hi Folks, both charliemom and lowensp,
You are not going to find original layouts or specs online if your home is older than 2 years. That's just the nature of the beast with our homes!
If your home is more than 3 years old, you need to take the steps that Greg mentioned. Contact the manufacture directly. Let them know why you need the specs and lay outs! Most likely, like Greg has mentioned, you will not get them! For some reason, they consider them trade secrets.
I've got a 34 year old home. I have no idea who manufactured it originally. Floor plans, for the most part are basic in all of our homes. Specs don't mean a lot if it's gone through one or even two owners.
If both of you could give us specific reasons why you need the info, we will do our best to provide it for you! You'll get more answers here than anywhere else!
Maureen
You are not going to find original layouts or specs online if your home is older than 2 years. That's just the nature of the beast with our homes!
If your home is more than 3 years old, you need to take the steps that Greg mentioned. Contact the manufacture directly. Let them know why you need the specs and lay outs! Most likely, like Greg has mentioned, you will not get them! For some reason, they consider them trade secrets.
I've got a 34 year old home. I have no idea who manufactured it originally. Floor plans, for the most part are basic in all of our homes. Specs don't mean a lot if it's gone through one or even two owners.
If both of you could give us specific reasons why you need the info, we will do our best to provide it for you! You'll get more answers here than anywhere else!
Maureen
Never discourage anyone...who continually makes progress, no matter how slow.
'Plato'
'Plato'
Hey Maureen,
You can find the answer to that question in the Floor Plan thread in the Decorating... topic. I replied when you asked me over there. Thanks for your help.
CM
You can find the answer to that question in the Floor Plan thread in the Decorating... topic. I replied when you asked me over there. Thanks for your help.
CM
the url charliemom gave for shult homes has a . at the end that's not needed.
Code: Select all
this one will work
http://www.schulthomes.com/contact_us/index.cfm
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Looking for Long Island, NY mobile home repair contractor
by cobrajetken » Sun Jul 23, 2017 9:08 am » in Mobile Home Repair - 0 Replies
- 88837 Views
-
Last post by cobrajetken
Sun Jul 23, 2017 9:08 am
-
-
-
Looking for company to do repairs on MH in OKC
by dbinokcok » Sun Mar 31, 2019 9:58 am » in Mobile Home Repair - 1 Replies
- 31305 Views
-
Last post by Greg
Sun Mar 31, 2019 2:36 pm
-
-
- 0 Replies
- 126493 Views
-
Last post by dan.zawxx
Mon Oct 12, 2020 9:01 pm
-
- 0 Replies
- 126089 Views
-
Last post by dan.zawxx
Mon Oct 12, 2020 9:03 pm
-
-
New Deck and Porch coming (photos included)
by vilmel2vilmel2 » Mon Jul 17, 2017 5:58 pm » in Mobile Home Repair - 4 Replies
- 44291 Views
-
Last post by vilmel2vilmel2
Wed Aug 02, 2017 10:29 am
-