Belly repair
Moderators: Greg, Mark, mhrAJ333, JD
So my next project is to repair the Belly Board which was invaded by raccoons. They ripped some holes and totally flattened the insulation in 1/4 of the home. The belly board is mostly intact and I would like to leave it that way as much as possible and slide in new insulation. The coons ripped a large hole in the middle which looks like the obvious place to insert new insulation. Unless someone has a better idea I was thinking I would cut a rectangular hole in each end and using a cord pull rolled insulation to the ends. The original insulation was an unfaced blanket. I was thinking I would used kraft faced rolls because it seems like it would slide in easier and it would hold together better while I pull it. Does this make sense? Are there problems I'm not aware of using the faced insulation? I know the facing usually goes toward the living space but in my case would be reversed. As I understand it the belly board is a vapor barrier itself so it seems like I would just have a double vapor barrier. I have the older fiber board belly board and would be patching it with the newer poly material. I have done some of this repair on the edges using the high strength adhesive and it seems to work pretty good. What is good to cut the fiber board? Utility knife just tears it. Maybe with a new blade? Saber saw? Dusty! How about cutting the poly stuff? It's slippery stuff and seems to just slide between the jaws of my shears. I'll be doing a lot of patching so I want to make it as easy as possible. I've used the Stay Put adhesive and it works good but pretty expensive. When I ran out I got some 3M High Strength 90 and as far as I can tell it's the same thing but a little cheaper and more available. Anyone know if there's a difference?
The cardboard type stuff cuts well with a fresh blade. Flip the blade or replace it every 20 LF or so, as soon as they slow down or snag. Blades are cheap. I cut the poly stuff with a good pair of fiskars scissors. I use 3M high-strength 90 sometimes and and I am pretty confident with it. Their data sheets are very similar. When checking data sheets, you can see where these adhesives are better for our purpose than other products.
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Belly wrap repair with furring strips
by mdnagel » Mon Sep 16, 2019 11:34 am » in Mobile Home Repair - 1 Replies
- 11251 Views
-
Last post by Greg
Mon Sep 16, 2019 6:47 pm
-
-
-
Belly board repair and Questions
by thedavidbieda » Tue May 19, 2020 8:18 pm » in Mobile Home Repair - 2 Replies
- 20716 Views
-
Last post by thedavidbieda
Fri May 22, 2020 9:38 am
-
-
-
I need input on best way to hang new copper or pex pipes from underside mobilehome without opening up belly board
by waitingtohear » Mon Jun 11, 2018 12:21 am » in Mobile Home Repair - 7 Replies
- 89699 Views
-
Last post by waitingtohear
Mon Jul 02, 2018 5:39 pm
-
-
- 6 Replies
- 9268 Views
-
Last post by Mark440
Tue Aug 07, 2018 3:15 pm
-
-
Best (1x4) replacement belly band board?
by mdnagel » Wed Jul 24, 2019 12:23 pm » in Mobile Home Repair - 0 Replies
- 27377 Views
-
Last post by mdnagel
Wed Jul 24, 2019 12:23 pm
-