I am putting together a double-wide that I moved.
I have been trying to figure out what to use for skirting: https://www.mobilehomerepair.com/phpbb/v ... f=6&t=8780
We came upon a [looks like ] nice option: Garage door panels.
We had a big hail storm in the area last spring and lots of Garage doors have been being replaced.
We got a bunch that are 16 feet long and 2 feet wide.
On a lot of them, I'm not even seeing where they are damaged.
Aluminum skin...
Even insulated... I don't know what the R-value is on these. I see R-values from ~6 to ~13.
Anybody see any problems with doing this?
Nifty new skirting option
Moderators: Greg, Mark, mhrAJ333, JD
Go for it!! If you can figure out a way to get them in place, it should work fine. You could even install a short overhead track and make the access panel "roll up"!
Greg
Greg
"If I can't fix it, I can screw it up so bad no one else can either."
-
- Posts: 4
- Joined: Sat May 07, 2011 4:02 pm
Not sure if this is feasible for you, but I liked like to mention an alternative in case it might work for others.
We put our MH on our ranch which is out in the middle of nowhere so we have to resort to sometimes unconventional methods when it comes to labor as it is all DIY.
We purchased metal roofing material to use for our skirting, which I think is similar to the garage panels, only your panels being insulated would be much better! To anchor them in place we used bridge timbers (like railroad ties only much much heavier) and staked them in place from behind with rebar. We used a level to line them up exactly with the house and then screwed the metal into the house edge as well as into the timbers. We have lots of wind and so far, they haven't moved a peg. We are very happy with our solution and it saved us tons of time as the bridge timbers are around 45' long.
I'm jealous of your insulated garage door panels! Sounds like a great idea.
We put our MH on our ranch which is out in the middle of nowhere so we have to resort to sometimes unconventional methods when it comes to labor as it is all DIY.
We purchased metal roofing material to use for our skirting, which I think is similar to the garage panels, only your panels being insulated would be much better! To anchor them in place we used bridge timbers (like railroad ties only much much heavier) and staked them in place from behind with rebar. We used a level to line them up exactly with the house and then screwed the metal into the house edge as well as into the timbers. We have lots of wind and so far, they haven't moved a peg. We are very happy with our solution and it saved us tons of time as the bridge timbers are around 45' long.
I'm jealous of your insulated garage door panels! Sounds like a great idea.
I also used the metal roofing material. Anchored treated 4 x 6's over a bed of pea gravel. Attached the panels to the outside edge of the 4x6...and let the top float behind the old plastic trim piece to keep it from buckling from cold/heat. Finished off with some drainage gravel - and so far its holding up just fine.
FWIW - you can buy the unpainted metal roofing panels and then paint it to whatever color you want. Just use some vinegar to 'etch' the finish on the panels before you apply any primer.
FWIW - you can buy the unpainted metal roofing panels and then paint it to whatever color you want. Just use some vinegar to 'etch' the finish on the panels before you apply any primer.
Opportunity has a shelf life.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 2 Replies
- 50859 Views
-
Last post by Mark440
Thu Apr 11, 2019 11:15 am
-
- 3 Replies
- 13090 Views
-
Last post by Jim from Canada
Sat Jul 15, 2017 8:29 am
-
- 3 Replies
- 17802 Views
-
Last post by Greg
Fri Oct 20, 2017 7:59 pm
-
-
Should skirting hang over edge of slab?
by mdnagel » Fri Nov 03, 2017 5:07 am » in Mobile Home Repair - 10 Replies
- 47962 Views
-
Last post by Greg
Wed Nov 08, 2017 8:24 pm
-
-
- 5 Replies
- 16074 Views
-
Last post by Greg
Thu Oct 18, 2018 7:38 pm