I have '92 Nashua with Blend Air 7681-7701 installed. Had furnace serviced today and asked tech to look at the Blend Air motor because it's become unbearably loud and I can't sleep. Options he offered were to replace the motor or permanently disconnect it. He said I had plenty of roof venting and that disconnecting Blend Air shouldn't cause any moisture problems. Thoughts?
<a href="http://www.flickr.com/photos/32698746@N02/10595240955/" title="photo 1 by kharndt, on Flickr"><img src="http://farm6.staticflickr.com/5545/1059 ... c92c_o.jpg" width="542" height="214" alt="photo 1"></a>
Can I disconnect BlendAir permanently?
Dale, thanks for responding! I've seen posts on how to disconnect, so I know it can be done.
1. Without Blend Air will the roof vents I have be adequate to keep the air moving (and moisture at bay)? Can you clarify: when you say "...when the blower comes on..." I assume you mean the furnace blower, correct?
2. Can it be turned off, or does it have to be unwired?
I so appreciate your help!!
1. Without Blend Air will the roof vents I have be adequate to keep the air moving (and moisture at bay)? Can you clarify: when you say "...when the blower comes on..." I assume you mean the furnace blower, correct?
2. Can it be turned off, or does it have to be unwired?
I so appreciate your help!!
There is a flex duct connected to the top of the furnace. Inside that duct, on top of the furnace, is an automatic damper....if so equipped. That damper should get either jammed open or removed to allow free flow of air into the furnace cabinet. The fan motor of the Blend Air system located in the roof vent assembly need not be messed with other than having it's wiring disconnected at the furnace. Basically you're just changing an active Blend Air system into a passive Blend Air system by using the blower of the furnace to pull fresh air into the home via the Blend Air ducting. The original system used a small fan motor to force that air into the furnace. Hope that answers your questions.
One last question -- or rather, confirming that what I will do is correct. In the photo, I am holding the green connections. I will pull the darker green wire (from Blend Air) out of that cluster and cap it with a wire nut. That leaves the thicker light green from the furnace and the thin green wire to the thermostat. I'll repeat for the red and white.
Anything else, besides taking care of the damper? Do I need to pull the white plug at the top of the Blend Air box?
This a great forum and I'm so appreciative of everyone who helps out!
Anything else, besides taking care of the damper? Do I need to pull the white plug at the top of the Blend Air box?
This a great forum and I'm so appreciative of everyone who helps out!
Must be another switch up near the motor in the Blend Air roof vent assembly. It could be humidity operated or temperature operated as an override to the low voltage wiring you have already disconnected. OR the switch I speak of is stuck in the ON position. You will have to go on the roof and just disconnect the primary wiring to the unit. Be sure to kill the breaker first. All that should be located under the Blend Air roof jack cap.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Can't read MFD size on rusted dual run cap.
by justplumducky » Sat Jul 01, 2017 6:31 pm » in Nordyne Service & Repair - 0 Replies
- 46693 Views
-
Last post by justplumducky
Sat Jul 01, 2017 6:31 pm
-
-
-
Can't get the furnace cover to go on
by nestsman » Sat Sep 30, 2017 4:53 pm » in Nordyne Service & Repair - 2 Replies
- 48439 Views
-
Last post by tkrueger
Sat May 05, 2018 9:12 pm
-
-
-
Porch roof - can I put plywood on it to support me?
by WholeHouseFan&Solar » Fri Sep 28, 2018 10:48 am » in Mobile Home Repair - 1 Replies
- 22872 Views
-
Last post by Greg
Fri Sep 28, 2018 8:14 pm
-
-
-
can i replace a single piece of skirting?
by backdrop001 » Thu Oct 10, 2019 11:54 am » in Mobile Home Repair - 1 Replies
- 9898 Views
-
Last post by Greg
Thu Oct 10, 2019 5:26 pm
-
-
-
Can I block up rim joist to level rim joist
by Jeremb2020 » Fri Feb 07, 2020 10:32 am » in Mobile Home Repair - 1 Replies
- 31181 Views
-
Last post by Greg
Fri Feb 07, 2020 2:28 pm
-