evcon furnace with motor constantly running
That is strange. Could be Robert will be along in a while. At this point I am kind of lost. Was there somekind of a part number on the old one? post all the numbers on the old one if you can.
God, grant me the serenity
to accept the things I cannot change;
the courage to change the things I can;
and the wisdom to know the difference.
to accept the things I cannot change;
the courage to change the things I can;
and the wisdom to know the difference.
Ok, is there a possibility it has just 4 spades and on one is something like this:
http://www.mobilehomerepair.com/media/img/G21-414.jpg
or this:
http://www.mobilehomerepair.com/media/img/G31-929.jpg
and it has two wires to it.
That would be 5 wires, but just 4 spades.
Thanks,
Robert
http://www.mobilehomerepair.com/media/img/G21-414.jpg
or this:
http://www.mobilehomerepair.com/media/img/G31-929.jpg
and it has two wires to it.
That would be 5 wires, but just 4 spades.
Thanks,
Robert
Last edited by Robert on Mon Oct 15, 2007 9:32 pm, edited 1 time in total.
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
oh yes that is very possible, so now what do i do, as i only have one blue (should have 2) and 3 blacks (should have 2) and i have a yellow which i dont know what to do with.
Hi,
You should have 2 Blue and 2 Blacks = 4 wires.
Since you have a Yellow making it 5 wires, see if you had one of those terminals like above with 2 wires connected to it ?
Thanks,
Robert
You should have 2 Blue and 2 Blacks = 4 wires.
Since you have a Yellow making it 5 wires, see if you had one of those terminals like above with 2 wires connected to it ?
Thanks,
Robert
Last edited by Robert on Mon Oct 15, 2007 9:45 pm, edited 1 time in total.
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
yes i believe it is like that, the two are very close together, looks like could be the same. two black wires are on that one, blue one is in the middle, another black one on the side and the yellow on the bottom
Is the relay next to the transformer inside the rectangular metal box at midway of furnace front ?
Just making sure we're on same page here.
If so, can you turn all power to furnace OFF, then remove those two blacks to see if they were on ONE spade by way of a terminal like I posted ?
Thanks,
Robert
Just making sure we're on same page here.
If so, can you turn all power to furnace OFF, then remove those two blacks to see if they were on ONE spade by way of a terminal like I posted ?
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Ok, so it only has 4 spades the same as the new one,,,,,,,,correct ?
Do you know where the wires go on new one or need help with that ?
Thanks,
Robert
Do you know where the wires go on new one or need help with that ?
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
i would love you to help me with that, it just confuses me that i have one extra wire, i am assuming that the yellow goes elsewhere???
Ok, draw on a piece of paper the shape of the old relay.
Put a mark where each wire goes and the color.
At place of the two blacks, write 2 blacks.
Tape those two blacks together so as to know they are THE two blacks.
Then remove the wires and remove screws to remove the relay.
Lay it beside the drawing you made.
Look at the relay, it should have numbers beside each spade.
What are they and with what wire ?
Give me this and I'll see if same numbers match for both relays.
Thanks,
Robert
Put a mark where each wire goes and the color.
At place of the two blacks, write 2 blacks.
Tape those two blacks together so as to know they are THE two blacks.
Then remove the wires and remove screws to remove the relay.
Lay it beside the drawing you made.
Look at the relay, it should have numbers beside each spade.
What are they and with what wire ?
Give me this and I'll see if same numbers match for both relays.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
ok i think i have this figured out, amazing hey? both blacks are linked together somehow and are on prong #2, yellow is on prong #3 the single black is on prong #4 and the blue is on prong #1. how does that sound?
Can you see at all where they go ?
Should be ok, but without testing, would like to be sure.
IF that is where they went on old relay, placing on same on new one should be fine though.
Thanks,
Robert
Should be ok, but without testing, would like to be sure.
IF that is where they went on old relay, placing on same on new one should be fine though.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Thank you Robert I never thought that someone would mistake a two wire tie in for two separate wires. LOL At least now it is straitened out.
God, grant me the serenity
to accept the things I cannot change;
the courage to change the things I can;
and the wisdom to know the difference.
to accept the things I cannot change;
the courage to change the things I can;
and the wisdom to know the difference.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Nordyne M1B1 furnace issue - thermostat c wire not hooked up correctly. It's running off atteries instead
by Tallestt » Mon Apr 20, 2020 6:27 am » in Nordyne Service & Repair - 1 Replies
- 43346 Views
-
Last post by taurolyon
Tue Jun 23, 2020 4:02 pm
-
-
-
Heat strip on while AC is running HELP Please!
by HelpNeeded » Wed Sep 19, 2018 6:47 pm » in Coleman Service & Repair - 0 Replies
- 35279 Views
-
Last post by HelpNeeded
Wed Sep 19, 2018 6:47 pm
-
-
-
Colman evcon presidental 7980B856 furnace will not stay on
by ezridersid » Sat Dec 21, 2019 8:52 pm » in Mobile Home Repair - 1 Replies
- 17302 Views
-
Last post by ezridersid
Sat Dec 21, 2019 9:04 pm
-
-
- 2 Replies
- 60295 Views
-
Last post by jazsimpson
Sat Jul 08, 2017 8:16 am
-
- 0 Replies
- 25763 Views
-
Last post by Tonystark
Fri Dec 07, 2018 12:30 pm