Hi,
Yes, temp should be 75* or above if possible. Furnace contains blower, a/c control box and a-coil, so should be part of an a/c service call always.
Gauge reading can be low and refrigerant charge still be ok, reason for leak inspection.
Refrigerant does not use itself up, only way to be low is from a leak.
Understand situation that leads to having to "hide" DIY.
The sequencer p/n given earlier can be seen and ordered through PayPal at the link given.
You can also call toll free after 9 AM CST Mon thru Fri to 1-877-263-7860 and charge to Visa or Mastercard.
Take care and best wishes,
Robert
Coleman Presidential II, M/N 3115A751: Blower will not stop
Ordered a sequencer today. One last dumb question:
In what general area will I find the sequencer? Since I haven't gotten a chance to test it out yet, I have no clue where it is located. Will it be inside of the box that has the Heat/Cool and On/Auto switches?
Thanks again for all your help.
In what general area will I find the sequencer? Since I haven't gotten a chance to test it out yet, I have no clue where it is located. Will it be inside of the box that has the Heat/Cool and On/Auto switches?
Thanks again for all your help.
Hi,
Look on back wall of furnace just above and left of elements.
Thanks for ordering, please let me know how it comes out.
You're very welcome, happy to help.
Take care and best wishes,
Robert
Look on back wall of furnace just above and left of elements.
Thanks for ordering, please let me know how it comes out.
You're very welcome, happy to help.
Take care and best wishes,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Opened up the door just below the control panel and found the sequencer easily accessible. Changed it out wire-for-wire and the new sequencer I ordered from you guys fixed everything. I have *cold* air for AC and warm/hot air for heat. The thermostat once again controls the fan blower motor as well.
Once again, thank you very much for all of your help.
Once again, thank you very much for all of your help.
Hi,
That's great, glad it is on line and working again. Thanks for update.
You're very welcome, happy to help out.
Take care and best wishes,
Robert
That's great, glad it is on line and working again. Thanks for update.
You're very welcome, happy to help out.
Take care and best wishes,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Coleman 6806a furnace doesn't stop heating even with tstat disconnected. Any ideas?
by Neighbor Bill » Mon Dec 31, 2018 1:01 pm » in Coleman Service & Repair - 1 Replies
- 41712 Views
-
Last post by Neighbor Bill
Mon Dec 31, 2018 1:06 pm
-
-
-
Drill a hold to stop a crack in the windshield?
by Qashisst » Thu Nov 28, 2019 4:40 am » in Off Topic Discussions - 0 Replies
- 31328 Views
-
Last post by Qashisst
Thu Nov 28, 2019 4:40 am
-
-
-
Where to stop new subflooring at door threshold
by mdnagel » Fri Feb 18, 2022 11:18 am » in Mobile Home Repair - 1 Replies
- 29542 Views
-
Last post by Mark440
Sun Apr 03, 2022 10:36 pm
-
-
-
LOUD Blower on Coleman Presidential 2 900759
by AuntKatie » Thu Apr 05, 2018 6:50 pm » in Coleman Service & Repair - 0 Replies
- 44830 Views
-
Last post by AuntKatie
Thu Apr 05, 2018 6:50 pm
-
-
-
Intertherm outdoor a/c unit, blower not turning off. Model unknown rating plate is faded out.
by tkrueger » Sat May 05, 2018 8:57 pm » in Nordyne Service & Repair - 0 Replies
- 116448 Views
-
Last post by tkrueger
Sat May 05, 2018 8:57 pm
-