**disclaimer** found this concoction to make Tim-bor and Bora-care. I have not tried this but I'm posting here to see what you think of it.
***ethylene glycol is HIGHLY POISONOUS to animals. even in small amounts, it is fatal. if it is applied to any object that an animal may come in contact with, they will invariably lick it. even after it dries, if it comes in contact with water and your animal drinks that water, it will poison them. its best to not even use this chemical if you have pets**
There are two commonly available inexpensive materials that will kill rot in wood and prevent its recurrence. First, there are borates (borax-boric acid mixtures) which have an established record in preventing rot in new wood and in killing rot organisms and wood-destroying insects in infested wood.
Second, there is Glycol, most readily available as auto antifreeze-coolant. Glycol is toxic to the whole spectrum of organisms from staphylococcus bacteria to mammals.
BORATE WOOD PRESERVATIVES:
COMMERCIAL AND HOME-BREWED
Commercial:
Tim-Bor®: Solid sodium octaborate; dissolves in water to make approx. a 10% solution containing 6.6% borate (B2O3); about $13/lb. Covers about 200 sq ft.
Bora-Care®: 40% solution of sodium octaborate in ethylene glycol; 27% borate content; $90/gal. for the concentrate.
Home-Brew Water Solution of Borates:
Based on U.S. Navy spec. of 60% borax-40% boric acid (this ratio gives the maximum solubility of borates in water);
#1. This is equiv. to Tim-Bor®... 6 parts of borax and 4 parts of boric acid.
To prepare one gallon of a 10% solution, start with an oversize container (larger than 1 gallon ) add 1 lb. of powder to appx 3 qts of water agitating until the powder has dissolved, then add additional water to end up with 1 gallon of mix. To prepare a 15% solution, add 1.5 lbs. of powder, then add the remainder of the water and mix as previously. Approximately 1 gallon of solution will be needed to treat 200 square feet of wood surface area. (Note: solutions should be used immediately and not stored.) .
EXAMPLE: Prepare 5 gallons of 10% solution:
Add four (4) gallons of clear, warm water to a six-gallon bucket.
Add five (5) lbs. of powder while gently stirring.
Add enough water to bring the final volume to 5 gallons, and continue to stir until all of the powder has dissolved.
Agitate the solution briefly at the beginning of each spray job, or after the solution has been standing for an extended period.
Do not spray or spill onto soil or foliage.
Apply two applications of a 10% solution to wood surfaces by brush or spray. Apply one application of a 15% solution to wood surfaces by brush or spray. Applications may be made to wood structures including decks, fences, steps, sheds, barns and other out-buildings.
#2: This is equivalent to Bora-Care®
Prepare the concentrate:
Mix 1 Gallon glycol antifreeze, 4 1/2 pounds borax, 3 1/2 pounds boric acid.
Mix the ingredients and heat till boiling gently. Boil off water until a candy thermometer shows 260°F. This removes most of the water of crystallization in the borax.
This solution is stable at 40°F and has a borate content of 26%. This is equivalent to Bora-Care® at about $90/gal. for the concentrate. The concentrate must be diluted with an equal volume of water before being applied.
Application: Add 1 gallon of water to every gallon of concentrate and stir thoroughly until solution is completely uniform. Always use diluted within 24 hours after mixing. If kept for longer periods of time, the active ingredient can drop out of the solution.
Note: is toxic to plants and shrubbery; if necessary, cover plants, root systems and surrounding soil with plastic to avoid contamination. Apply only to bare wood. Remove any finish or water repellent coating before applying . Wood surfaces should be free of dirt and other contaminates. Apply diluted by spray or brush to all exposed wood surfaces. It may occasionally be necessary to apply more than one coat of to attain the recommended application rate. This is especially true for larger, smooth surfaced wood members. Wood surfaces should be allowed to dry for at least 2 hours between applications. Do not apply in the rain or snow. If inclement weather is expected, protect exposed treated surface with a plastic tarp for at least 24 hours after treatment. One gallon of concentrate will treat up to 800 board feet of wood. Only diluted should be applied to any wood surface. Prior to application, check wood surfaces for an existing water repellent finish by spraying a small amount of water onto the surface of the wood or logs. If the water beads up or is not absorbed into the wood, a finish is present which must be removed before applying the diluted solution.
can this get rid of wood rot and termites ?
Moderators: Greg, Mark, mhrAJ333, JD
- thatswhoiam
- Posts: 56
- Joined: Mon Mar 17, 2014 12:27 am
Last edited by thatswhoiam on Thu Jun 12, 2014 7:33 pm, edited 2 times in total.
Well I guess that it should be stable enough not to blow up in your face. To me it seems like a lot of work to go through, but I am too far north to be bothered by termites and I use pressure treated wood when I build anything exposed to weather.
Greg
Greg
"If I can't fix it, I can screw it up so bad no one else can either."
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Can't get the furnace cover to go on
by nestsman » Sat Sep 30, 2017 4:53 pm » in Nordyne Service & Repair - 2 Replies
- 48448 Views
-
Last post by tkrueger
Sat May 05, 2018 9:12 pm
-
-
-
Silicone calking for concrete, wood and metal?
by mdnagel » Thu Aug 22, 2019 11:24 pm » in Mobile Home Repair - 4 Replies
- 20315 Views
-
Last post by Lancer21
Sat Aug 31, 2019 2:59 am
-
-
-
Over $400 to get new vinyl for bathroom floor?
by cat_mobile » Sun Oct 01, 2017 12:30 pm » in Mobile Home Repair - 1 Replies
- 29819 Views
-
Last post by Greg
Sun Oct 01, 2017 6:24 pm
-
-
- 2 Replies
- 23376 Views
-
Last post by mdnagel
Thu Jun 13, 2019 4:34 am
-
- 1 Replies
- 25914 Views
-
Last post by Greg
Fri Oct 25, 2019 7:57 pm