We have a Coleman Evcon DLAS075BDD which has recently come up with the flash code of ignition failure. Have checked all parts concerned and have narrowed it down to the integrated circuit board. What I want to know is what is the difference between 7990-319P and 7990-320P?
Thanks,
WrenchBender
Coleman Evcon DLAS075BDD
Unless you have both boards in front of you there is no way to tell the difference from here. The manufacturer made the boards different for some reason and more that likely it is a change of component used in the furnace that necessitated the board difference. I know you cannot sub one of those boards for another of a different number. The furnace is designed to run with just one model number board. To much of a risk to try a different board unless specified by the factory. More damage could be done to the gas valve ignition system ETC.
God, grant me the serenity
to accept the things I cannot change;
the courage to change the things I can;
and the wisdom to know the difference.
to accept the things I cannot change;
the courage to change the things I can;
and the wisdom to know the difference.
Great....thank you! The part number on the board in the furnace is 7990-320P but I have saw on various sites that 7990-319P is also compatable with our furnace. Will stick to the same circuit board that is in the furnace.
Again, thank you!
WrenchBender
Again, thank you!
WrenchBender
Hi,
7990-319P IS the correct board for that furnace.
Control Board 7990-319P @ $171 + $8 shipping.
It can be seen and ordered from this page:
http://www.mobilehomerepair.com/ColemanGas.html
Take care and best wishes,
Robert
7990-319P IS the correct board for that furnace.
Control Board 7990-319P @ $171 + $8 shipping.
It can be seen and ordered from this page:
http://www.mobilehomerepair.com/ColemanGas.html
Take care and best wishes,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
We replaced the mother board last spring and now it is has started flashing the same "ignition failure" code. What gives? I am stumped....any suggestions???
Hi,
The top three causes of Ignition Failure code are:
Dirty/damaged remote sensor:
http://www.mobilehomerepair.com/TechTip1.html
Hot Surface Ignitor (inspect real well)/ It is very fragile and easily broken.
DO NOT touch either with bare fingers or hands.
Faulty Gas Valve - Test GV terminals for 24-28VAC after Ignitor has energized with 120VAC for approx. 35 seconds.
Gas Valve will energize for approx. 6 seconds, if remote sensor senses flame it will remain energized.
Thanks,
Robert
The top three causes of Ignition Failure code are:
Dirty/damaged remote sensor:
http://www.mobilehomerepair.com/TechTip1.html
Hot Surface Ignitor (inspect real well)/ It is very fragile and easily broken.
DO NOT touch either with bare fingers or hands.
Faulty Gas Valve - Test GV terminals for 24-28VAC after Ignitor has energized with 120VAC for approx. 35 seconds.
Gas Valve will energize for approx. 6 seconds, if remote sensor senses flame it will remain energized.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Similar Topics
- Replies
- Views
- Last post
-
- 0 Replies
- 110034 Views
-
Last post by cwwhite75
Sat Feb 29, 2020 8:46 am
-
-
Colman evcon presidental 7980B856 furnace will not stay on
by ezridersid » Sat Dec 21, 2019 8:52 pm » in Mobile Home Repair - 1 Replies
- 17301 Views
-
Last post by ezridersid
Sat Dec 21, 2019 9:04 pm
-
-
-
Transformer burning out in an Evcon DES 80
by BigDave67s » Wed Dec 29, 2021 10:01 pm » in Coleman Service & Repair - 0 Replies
- 111965 Views
-
Last post by BigDave67s
Wed Dec 29, 2021 10:01 pm
-
-
-
Evcon Heat Pump - Air Conditioner Model No. BRHS036B Making HUM Before Starting
by Dave_L » Tue Aug 29, 2023 1:26 am » in Coleman Service & Repair - 0 Replies
- 126524 Views
-
Last post by Dave_L
Tue Aug 29, 2023 1:26 am
-
-
- 2 Replies
- 60294 Views
-
Last post by jazsimpson
Sat Jul 08, 2017 8:16 am