I have a double wide and want to put a ceiling fan in the dining room. Because of the ceiling (about 7-8 foot high) I will put in a flush mounted fan. My question is I have a roof and then tin and then ceiling panel. With no wood to support the fan, what should I do? My brother suggested a box mount on the roof and then put a pipe with all thread through the roof to the ceiling and mount fan to that. Then caulk the hell out of the mount box. Does this sound feasible?
thanks,
john
ceiling fan installation
Moderators: Greg, Mark, mhrAJ333, JD
Hi,
Going to move this to mobile home repair forum for more views and answers.
There are a couple options, the one you asked about not being one of them.
Please follow it over there.
Thanks,
Robert
Going to move this to mobile home repair forum for more views and answers.
There are a couple options, the one you asked about not being one of them.
Please follow it over there.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
Here is a solution I usually use for fans in mobile home ceilings, especially homes with 1x2 and 2x2 trusses. I will cut a 19" x 19" square of plywood and mount it across two trusses. A hole can be cut in the middle of the plywood for the fan electrical box. A short piece of 2x4 can be threaded through this hole (after slight modification - angle cut the sides) to be used to screw the electrical box to. Drill a 1" hole for wire or run the wire. The 2x4 can be fastened with glue and brads. The electrical box can be attached to the 2x4 with 1 1/2" screws. Trim the edges of the plywood with quarter round and paint the wood the ceiling color or color of your choice. If you want to stain the wood instead of paint, you can buy 24" x 24" pieces of oak plywood at most home stores. Makes for a nicer looking stain job.
Now the fan weight is supported by 2 trusses and the box can be mounted with 4 screws to make it stable. That is how I do it. I do not use the adjustable fan bar on 1x2 and 2x2 trusses. JMO
JD
Now the fan weight is supported by 2 trusses and the box can be mounted with 4 screws to make it stable. That is how I do it. I do not use the adjustable fan bar on 1x2 and 2x2 trusses. JMO
JD
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 2 Replies
- 19727 Views
-
Last post by Joe Freeman
Tue Aug 01, 2017 10:13 am
-
-
How to Select the Right Ceiling Fan
by Divyank1106 » Tue Jun 11, 2019 12:31 am » in Off Topic Discussions - 1 Replies
- 18473 Views
-
Last post by spazatac
Sun Jun 30, 2019 10:39 am
-
-
-
Question about installation over existing floor
by Stormymonday » Sat Sep 15, 2018 3:06 pm » in Off Topic Discussions - 1 Replies
- 27855 Views
-
Last post by Greg
Fri Sep 21, 2018 7:08 pm
-
-
-
A/C and heat comes from the ceiling vents. Are the existing floor vents necessary?
by NanaMary » Tue Nov 21, 2017 12:35 pm » in All Other HVAC Questions - 2 Replies
- 55610 Views
-
Last post by NanaMary
Fri Nov 24, 2017 11:14 am
-
-
- 1 Replies
- 9137 Views
-
Last post by Greg
Fri Jan 26, 2018 7:55 pm